RSX-11M-PLUS V4.6 BL87 2044.KW System:"Baseline" >RED DU:=SY: >RED DU:=LB: >RED DU:=SP: >MOU DU0:"RSX11MPBL87" >@[2,54]BASTART.CMD >SET /CRASHDEV=MM0: SET -- Crash device MM000: has been successfully loaded >; >; >; RSX-11M-PLUS V4.6 Distribution Kit >; >; This is the baseline system of the RSX-11M-PLUS V4.6 >; distribution kit. This system contains an assortment of >; devices and may in fact be of some use on your target >; system. The main purpose of the baseline system, however, >; is to provide a working system environment which may be >; used to generate a custom-tailored operating system for >; your target hardware. We will now provide instructions >; to guide you through the startup procedure. >; >* Please enter time and date (Default:19-JUL-2017 12:30) [S]: >; >; Now allocate checkpoint space for use by system utilities. >; >ACS SY:/BLKS=1024. >; >; The following information is necessary for this command file >; to correctly access the remainder of the distribution kit. >; >* Did you receive your RSX-11M-PLUS distribution kit on magnetic tape? [Y/N]: Y >; >; Please enter the name of the magnetic tape drive, which should >; still contain the distribution tape. The name is of the form: >; >; MM1: or >; MS0: etc... >; >* Which tape drive contains the distribution tape [S]: MU0: >; >; We will now set the CSR of the controller that will be >; used to bring in the remainder of the distribution kit to >; the standard value. If your controller is not at this address >; it will be necessary for you to manually configure the system >; by issuing the appropriate CON commands. Answer Yes to the >; manual configuration question to do this. If your controller >; is at the standard address, you do not have to do a manual >; configuration. >; >CON SET MSA CSR=160000 >CON SET MTA CSR=160000 >CON SET RHC CSR=160000 >CON SET MUA VEC=224 >; >; We will now bring on line all devices which were generated into >; this baseline image and which exist in your hardware system. >; >; If there is hardware in your system occupying a control >; register address which conflicts with a standard DIGITAL >; register assignment, it is possible that the "CON ONLINE >; ALL" command might cause a system crash. This is because >; a supplied device driver is attempting to manipulate foreign >; hardware or the CSR address assignments in your system are >; different from those assumed in this baseline configuration. >; On the first pass through this file please answer No to the >; following question. If such a mismatch exists and a crash >; does occur, rebootstrap the baseline system and answer Yes >; to this question. Instructions will then be provided to help >; circumvent the problem. >; >* Do you need to do manual configuration? [Y/N]: >; >CON ONLINE ALL >; >; Prepare to bring in the remainder of the distribution kit >; >* Is your target system disk an RC25, RK07, or RD52? [Y/N]: >; >; Since the files in the second backup set are not necessary to generate >; your system you may wish to skip the verify pass to save time. >; >* Do you want to verify the second backup set? [Y/N]: Y >; >; We will now mount the tape in MU0: for access by BRU. >; >MOU MU0:/FOR >; >; Ensure that the BRU task is installed. >; >INS $BRU >; >; We will now load the remainder of the distribution kit. >; >TIME 12:31:01 19-JUL-17 >; >BRU /BAC:MPBL87SRC/UFD/NOINI/VER MU0: SY: BRU - Starting Tape 1 on MU0: BRU - End of Tape 1 on MU0: BRU - Starting verify pass Tape 1 on MU0: BRU - End of Tape 1 on MU0: BRU - Completed >; >DMO MU0:/LOCK=UNLOAD 12:31:17 *** MU0: -- Dismount complete DMO -- TT0: dismounted from MU0: *** Final dismount initiated *** >; >TIME 12:31:17 19-JUL-17 >; >; We will now create any UFDs that must be created on your disk(s). >; You will not see the UFD commands. >; >TIME 12:31:17 19-JUL-17 >; >; >; The preparation of the RSX-11M-PLUS kit is now complete. The next >; time this disk is bootstrapped, this dialog will only be repeated >; on request. We will now record the successful installation in the >; log file on the new system disk, and either exit if the installation >; was done on line, or proceed with the normal startup sequence if the >; baseline system was used. >; >SET /UIC=[2,54] >PIP LB:[1,1]KITIDENT.DAT/AP=LB:[2,54]INSTALOG.DAT >; >; >SET /UIC=[200,200] >; PLEASE NOTE >; >; If you have not yet read the system release notes, please do so >; now before attempting to perform a SYSGEN or to utilize the new >; features of this system. >; >; >; In order to start the SYSGEN process, type: >; >; >@SYSGEN >; >; When SYSGEN has completed and your generated system is >; running, you may wish to edit several supplied prototype >; command and text files to suit your system and application: >; >; File Purpose >; ---- ------- >; [0,0]RSX11.SYS An account/password file >; This file does contain privileged accounts. >; >; [1,2]STARTUP.CMD (This file) Invoked at bootstrap time to >; control bringing up the system. >; >; [1,2]QMGSTART.CMD Invoked by STARTUP to start up the Queue >; Manager and spooling system. >; >; [1,2]SHUTUP.CMD Invoked by SHUTUP when taking down the system >; to perform system dependent shutdown tasks. >; >; [1,2]QMGSTOP.CMD Invoked by SHUTUP to stop the Queue Manager >; and spooling system. >; >; [1,2]LOGIN.TXT Displayed on user's terminal when logging in. >; >; [1,2]BATCH.TXT Displayed at the beginning of each batch log >; file. >; >; >ELI /LOG/LIM >CLI /INIT=DCL/CTRLC/DPR="<15><12>/$ /" >INS LB:[1,1]RMSRESAB.TSK/RON=YES/PAR=GEN >INS LB:[1,1]RMSLBL.TSK/RON=YES/PAR=GEN >INS LB:[1,1]RMSLBM.TSK/RON=YES/PAR=GEN >INS $QMGCLI >INS $QMGCLI/TASK=...PRI >INS $QMGCLI/TASK=...SUB >QUE /START:QMG >INS $QMGPRT/TASK=PRT.../SLV=NO >QUE LP0:/CR/NM >START/ACCOUNTING >CON ESTAT LP0: >QUE LP0:/SP/FL:2/LOWER/FO:0 >QUE BAP0:/BATCH >QUE LP0:/AS:PRINT >QUE BAP0:/AS:BATCH >@ >RUN $SHUTUP RSX-11M-PLUS Shut down program Enter minutes to wait before shutdown: Reason for shutdown ( for none): OK to shutdown? [Y/N]: Y All further logins are disabled 19-JUL-17 12:33 System is now shutting down -- BASLIN QUE /STO:QMG > STOP/ACCOUNTING SHUTUP 12:33:49 SYSLOG -- 47. Exiting > @LB:[1,2]SHUTUP >@ > ELI /NOLOG > ACS DU0:/BLKS=0. ACS -- Checkpoint file now inactive > DMO DU0:/DEV/LOCK=V DMO -- System disk being dismounted DMO -- SYSTEM dismounted from DU0: *** Final dismount initiated *** 12:33:50 *** DU0: -- Dismount complete > SHUTUP operation complete RSX-11M-PLUS V4.6 BL87 2044.KW System:"Baseline" >RED DU:=SY: >RED DU:=LB: >RED DU:=SP: >MOU DU0:"RSX11MPBL87" >@[2,54]BASTART.CMD >SET /CRASHDEV=MM0: SET -- Crash device MM000: has been successfully loaded >; >* Do you wish to see the Installation Notes? [Y/N]: >SET /UIC=[200,200] >; >; PLEASE NOTE >; >; If you have not yet read the system release notes, please do so >; now before attempting to perform a SYSGEN or to utilize the new >; features of this system. >; >; >; In order to start the SYSGEN process, type: >; >; >@SYSGEN >; >; When SYSGEN has completed and your generated system is >; running, you may wish to edit several supplied prototype >; command and text files to suit your system and application: >; >; File Purpose >; ---- ------- >; [0,0]RSX11.SYS An account/password file >; This file does contain privileged accounts. >; >; [1,2]STARTUP.CMD (This file) Invoked at bootstrap time to >; control bringing up the system. >; >; [1,2]QMGSTART.CMD Invoked by STARTUP to start up the Queue >; Manager and spooling system. >; >; [1,2]SHUTUP.CMD Invoked by SHUTUP when taking down the system >; to perform system dependent shutdown tasks. >; >; [1,2]QMGSTOP.CMD Invoked by SHUTUP to stop the Queue Manager >; and spooling system. >; >; [1,2]LOGIN.TXT Displayed on user's terminal when logging in. >; >; [1,2]BATCH.TXT Displayed at the beginning of each batch log >; file. >; >; >* Please enter time and date (Default:19-JUL-2017 12:36) [S]: >ACS SY:/BLKS=1024. >CON ONLINE ALL >ELI /LOG/LIM >CLI /INIT=DCL/CTRLC/DPR="<15><12>/$ /" >INS LB:[1,1]RMSRESAB.TSK/RON=YES/PAR=GEN >INS LB:[1,1]RMSLBL.TSK/RON=YES/PAR=GEN >INS LB:[1,1]RMSLBM.TSK/RON=YES/PAR=GEN >INS $QMGCLI >INS $QMGCLI/TASK=...PRI >INS $QMGCLI/TASK=...SUB >QUE /START:QMG >INS $QMGPRT/TASK=PRT.../SLV=NO >QUE LP0:/CR/NM >START/ACCOUNTING >CON ESTAT LP0: >QUE LP0:/SP/FL:2/LOWER/FO:0 >QUE BAP0:/BATCH >QUE LP0:/AS:PRINT >QUE BAP0:/AS:BATCH >@ > >MOU DU3:/OVR/VI Volume Information Class: Files-11 Device: DU03 Volume label:RSX11MPBL40 Pack serial: 00000001237 Owner: [1,1] Protection: [RWCD,RWCD,RWCD,RWCD] Default: [RWED,RWED,RWED,R] Processor: F11ACP >INS $BRU >BRU/MOU/NOINI/UFD/VER DU3:[1,5],[HUNTA] DU: BRU - Starting verify pass BRU - Completed >DMO DU3: DMO -- TT0: dismounted from DU3: *** Final dismount initiated *** 12:41:41 *** DU3: -- Dismount complete > >HEL 10/1/xxxx RSX-11M-PLUS V4.6 BL87 [2,54] System BASLIN 19-JUL-17 12:45 Logged on Terminal TT0: as KXX1 Good Afternoon ***************************************************************** * * * Welcome to RSX-11M-PLUS * * * * Version 4.6 Base level 87 * * This is file LB:[1,2]LOGIN.TXT * * * ***************************************************************** >@LOGIN.CMD >SET /EBC=TI: >SET /NONAMED >SET /UIC=[200,200] >ASN = >MOU DU3:/OVR/VI Volume Information Class: Files-11 Device: DU03 Volume label:RSX11MPBL40 Pack serial: 00000001236 Owner: [1,1] Protection: [RWCD,RWCD,RWCD,RWCD] Default: [RWED,RWED,RWED,R] Processor: F11ACP >SET /UIC=[11,10] >PIP /FO=DU3:DWDRV.MAC,DWTAB.MAC,MYDRV.MAC,MYTAB.MAC >SET /UIC=[200,200] >DMO DU3: DMO -- TT0: dismounted from DU3: *** Final dismount initiated *** 12:59:11 *** DU3: -- Dismount complete > >@SYSGEN >; >; RSX-11M-PLUS V4.6 BL87 SYSGEN >; >; Copyright (c) 1995-1999 by Mentec Inc., U.S.A. >; >SET /DPRO=[RWED,RWED,RWE,R] >; >; To exit from the SYSGEN procedure at any time, type CTRL/Z. >; >; If you are unsure of the answer to a question for which a de- >; fault answer exists, use the default answer. >; >; >; >;=================================================== >; Choosing SYSGEN Options 19-JUL-17 at 12:59 >;=================================================== >; >; >; >; Every question is preceded by a question number (for example SU010) >; which you can use to find the explanation of the question in the >; RSX-11M-PLUS System Generation and Installation Guide. >; >; An explanation of every question is also available by pressing >; the ESC key (or the ALTMODE key) in response to the question. >; >; If you are unfamiliar with the SYSGEN procedure, the explanation of >; each question can be printed automatically before the question. >; >* SU010 Do you always want the explanation printed? [Y/N D:N]: >; >; SYSGEN always creates saved answer files containing your responses >; to the SYSGEN questions: >; >; SYSGENSA1.CMD Setup questions, Executive options >; SYSGENSA2.CMD Peripheral configuration >; SYSGENSA3.CMD Nonprivileged task builds >; >; You should perform a PREPGEN first to create saved answer files, and >; then perform a SYSGEN, specifying those saved answer files as input >; to the Executive, peripheral, and nonprivileged task build sections. >; >* SU020 Do you want to use a saved answer file as input for >* the Executive options? [Y/N D:N]: >; >* SU040 Do you want to use a saved answer file as input for >* the peripheral configuration? [Y/N D:N]: >; >* SU060 Do you want to use a saved answer file as input for >* the nonprivileged task builds? [Y/N D:N]: >; >* SU080 Do you want to do a PREPGEN? [Y/N D:N]: Y >; >* SU090 Enter the name of the disk drive containing your >* target system disk [ddnn:] [S R:2-5]: DU0 >; >ASN DU0:=IN: >ASN DU0:=OU: >ASN DU0:=LB: >ASN DU0:=WK: >ASN DU0:=TK: >ASN DU0:=BC: >ASN DU0:=LI: >ASN DU0:=OB: >ASN DU0:=EX: >ASN DU0:=MP: >; >* SU100 Do you want to run Autoconfigure on the host system >* hardware? [Y/N D:N]: >; >; You can: >; >; o do a complete SYSGEN >; >; o continue a previous SYSGEN from where you left off >; >; o do an individual section of SYSGEN >; >; >* SU120 Do you want to do a complete SYSGEN? [Y/N D:Y]: >; >!INS [3,54]MAC/TASK=MACT0 >!INS [3,54]PIP/TASK=PIPT0 >!INS [3,54]LBR/TASK=LBRT0 >!INS [3,54]TKB/TASK=TKBT0 >!INS [3,54]VMR/TASK=VMRT0 >; >; >; >;====================================================== >; Choosing Executive Options 19-JUL-17 at 12:59 >;====================================================== >; >; >; >; The answers to the questions in this section are put in the saved >; answer file [200,200]SYSGENSA1.CMD. >; >; Enter a comment for inclusion in the SYSGENSA1 saved answer file. >; The comment may contain more than one line. The "V" in the right >; margin below marks the maximum line length. When you are done, >; press RETURN in response to the prompt. >; V >* Comment [S R:0.-55.]: DVK version RSX-11M-PLUS 4.6 >* Comment [S R:0.-55.]: >; >* CE010 What is your target processor type? [S R:3.-12. D:"11/70"]: >; >* CE020 Do you want the Full-functionality Executive? [Y/N D:Y]: N >; >; The User-tailored Executive will require you to answer at least >; twenty additional questions specifying which standard RSX-11M-PLUS >; features you wish to disable. You should not choose the User-tailored >; Executive unless you need to disable specific RSX-11M-PLUS features. >; >; >* CE030 Do you want to reconsider your selection? [Y/N D:N]: >; >* CE050 Do you want Executive data space support? [Y/N D:N]: >; >* CE070 Do you want support for task headers out-of-pool? [Y/N D:N]: Y >; >* CE075 Do you want extended logical name support? [Y/N D:N]: Y >; >* CE080 Do you want supervisor-mode library support? [Y/N D:N]: >; >* CE094 Do you want support for the fast map facility? [Y/N D:N]: Y >; >* CE100 Do you want all DIGITAL-supplied drivers and their data bases >* to be loadable? [Y/N D:N]: Y >; >* CE120 Do you want support for communications products >* (such as DECnet, PSI, and LAT)? [Y/N D:N]: >; >* CE130 What is the system name? [S R:0-6 D:"RSXMPL"]: KPXX01 >; >* CE140 Do you want shadow recording support? [Y/N D:N]: >; >* CE145 Do you want disk data caching support? [Y/N D:N]: Y >; >* CE150 Do you want console driver support? [Y/N D:N]: >; >* CE160 Do you want accounting support? [Y/N D:N]: Y >; >* CE170 Do you want to include the batch processor? [Y/N D:N]: Y >; >* CE190 Do you want to include DCL and alternate CLI support? [Y/N D:N]: Y >; >* CE194 Do you want CTRL/C abort support? [Y/N D:N]: Y >; >* CE195 Do you want extended security support? [Y/N D:N]: >; >; Extended security support provides for password expiration, >; account lifetimes, account expiration, and other functions >; similar to those provided under VAX/VMS. >; >* CE195 Do you want extended security support? [Y/N D:N]: Y >; >* CE197 Do you want alternate checkpointing support? [Y/N D:N]: >; >; Alternate checkpoint support allows the executive to choose >; partitions for checkpointing based on where the last partition >; was loaded, or in the traditional first available location. >; >; This alternate method is similar to the P/OS method, and >; minimized the amount of thrashing which occurred in small >; memory systems, or when using checkpointable tasks which have >; long outstanding non-buffered I/O. >; >* CE197 Do you want alternate checkpointing support? [Y/N D:N]: Y >; >* CE200 Which FCP do you want? [S R:1-6 D:"FCPLRG"]: >; >* CE210 Do you want support for file windows in secondary pool? [Y/N D:N]: Y >; >* CE214 Do you want decimal version numbers in >* file specifications? [Y/N D:N]: Y >; >* CE215 Do you want the default date format to be >* ISO 8601:1988 compliant? [Y/N D:N]: >; >; This option determines if dates should be displayed according to >; ISO 8601 format specification. >; >; For example; if the date February 1, 2000 should be displayed >; as 2000-02-01 >; >; >* CE215 Do you want the default date format to be >* ISO 8601:1988 compliant? [Y/N D:N]: Y >; >* CE230 What is the default virtual terminal unit buffer >* size? [D R:1.-512. D:120.]: 512. >; >* CE240 What is the maximum virtual terminal unit buffer >* size? [D R:1.-512. D:184.]: 512. >; >* CE250 Do you want character translation support? [Y/N D:N]: Y >; >* CE260 Enter unsolicited input time-out (in seconds) [D R:0.-255. D:30.]: >; >* CE264 Do you want IP11 industrial I/O subsystem support? [Y/N D:N]: >; >* CE270 Do you want to include XDT? [Y/N D:N]: >; >* CE280 Enter the crash notification device CSR >* address [O R:160000-177700 D:177564]: >; >; Note: Enter both the device and the logical unit number. >; For example, MM0: or DL1:. >; >; Note: Enter XX: if you desire loadable DU:, DL:, MU:, MS: or MM: >; crash driver support. >; >* CE290 On what device and unit do you want crash dumps >* to be written? [S R:2-6]: MU0 >; >* CE300 Enter the initial number of virtual disks to be >* included [D R:0.-16. D:2.]: >; >; Virtual disks allow the system to better manage large amounts >; of storage. If you expect to hardware of software boot virtual >; drives, select the maximum depth of virtual devices which will >; be booted. >; >* CE300 Enter the initial number of virtual disks to be >* included [D R:0.-16. D:2.]: 16. >; >* CE310 Enter memory size (in K words) [D R:256.-2044. D:256.]: 512. >; >* CE315 Support UNIBUS memory occupying UNIBUS map address space? [Y/N D:N]: >; >; Some PDP-11/44 and PDP-11/84 systems are configured with UNIBUS >; memory which disables some UNIBUS Map registers. If support for >; UNIBUS memory is selected, then special UNIBUS memory partitons >; are supported, and specific UMR resources reserved when UNIBUS >; memory is detected on the system. If your system does not contain >; any memory devices on the UNIBUS, this option will have no effect. >; >* CE315 Support UNIBUS memory occupying UNIBUS map address space? [Y/N D:N]: >; >* CE320 Do you want floating point processor support? [Y/N D:N]: Y >; >* CE330 Is your system clock programmable (KW11-P)? [Y/N D:N]: >; >* CE350 Is your line frequency 50 Hz? [Y/N D:N]: Y >; >; >; >;============================================================= >; Choosing Peripheral Configuration 19-JUL-17 at 13:05 >;============================================================= >; >; >; >; The answers to the questions in this section are put in the saved >; answer file [200,200]SYSGENSA2.CMD. >; >; Enter a comment for inclusion in the SYSGENSA2 saved answer file. >; The comment may contain more than one line. The "V" in the right >; margin below marks the maximum line length. When you are done, >; press RETURN in response to the prompt. >; V >* Comment [S R:0.-55.]: DVK version RSX-11M-PLUS 4.6 >* Comment [S R:0.-55.]: >; >; >* CP0604 How many RH controllers do you have? [D R:0.-15. D:4.]: 0 >; >; >; DK: controller: RK11 devices: RK05, RK05F >; >* CP2204 How many RK11 cartridge disk controllers do you have? [O D:0]: >; >; >; DM: controllers: RK611, RK711 devices: RK06, RK07 >; >* CP2404 How many RK611/711 disk cartridge controllers do >* you have? [O D:0]: >; >; >; DL: controllers: RL11, RLV12 devices: RL01, RL02 >; >* CP2604 How many RL11/RLV11 disk cartridge controllers do >* you have? [O D:0]: >; >; >; DP: controller: RP11 devices: RP02, RPR02, RP03 >; >* CP2804 How many RP11 disk pack controllers do you have? [O D:0]: 1 >; >* CP2808 How many RP02/RPR02/RP03 disk drives do you >* have? [D R:1.-63. D:1.]: 8 >; >; >* CP2836 What is the physical unit number of DP0:? [O R:0-7 D:0]: >; >* CP2860 Is DP0: an RP02, RPR02, or RP03? [S R:4-5 D:"RP03"]: RP02 >; >; >* CP2836 What is the physical unit number of DP1:? [O R:0-7 D:1]: >; >* CP2860 Is DP1: an RP02, RPR02, or RP03? [S R:4-5 D:"RP03"]: RP02 >; >; >* CP2836 What is the physical unit number of DP2:? [O R:0-7 D:2]: >; >* CP2860 Is DP2: an RP02, RPR02, or RP03? [S R:4-5 D:"RP03"]: RP02 >; >; >* CP2836 What is the physical unit number of DP3:? [O R:0-7 D:3]: >; >* CP2860 Is DP3: an RP02, RPR02, or RP03? [S R:4-5 D:"RP03"]: RP02 >; >; >* CP2836 What is the physical unit number of DP4:? [O R:0-7 D:4]: >; >* CP2860 Is DP4: an RP02, RPR02, or RP03? [S R:4-5 D:"RP03"]: RP02 >; >; >* CP2836 What is the physical unit number of DP5:? [O R:0-7 D:5]: >; >* CP2860 Is DP5: an RP02, RPR02, or RP03? [S R:4-5 D:"RP03"]: RP02 >; >; >* CP2836 What is the physical unit number of DP6:? [O R:0-7 D:6]: >; >* CP2860 Is DP6: an RP02, RPR02, or RP03? [S R:4-5 D:"RP03"]: RP02 >; >; >* CP2836 What is the physical unit number of DP7:? [O R:0-7 D:7]: >; >* CP2860 Is DP7: an RP02, RPR02, or RP03? [S R:4-5 D:"RP03"]: RP02 >; >; >* CP2868 Enter the vector address of DPA [O R:60-774 D:254]: >; >* CP2872 What is its CSR address? [O R:160000-177700 D:176714]: >; >; DP Configuration >; >; Physical Unit Number >; >; 0 1 2 3 4 5 6 7 >; >; DPA DP0: DP1: DP2: DP3: DP4: DP5: DP6: DP7: >; >; >; >; DU: controllers: RQZX1, RQDX1, RQDX2, RQDX3, >; RUX50, RQC25, KDA50, UDA50 >; >; devices: RX33, RX50, RD31, RD51, RD52, RD53, RD54, >; RC25, RA60, RA70, RA71, RA72, RA80, RA81, >; RA82, RA90, RA92, RZ23L, RZ24L, RZ26x, RZ29B >; >; The total of DU and MU controllers cannot be greater than 10. >; >* CP3004 How many MSCP disk controllers do you have? [D R:0.-10. D:0.]: 1 >; >* CP3008 How many physical MSCP disk drives do you have? [D D:1.]: 4 >; >; >* CP3036 What is the physical unit number of DU0:? [O R:0-377 D:0]: >; >; >* CP3036 What is the physical unit number of DU1:? [O R:0-377 D:1]: >; >; >* CP3036 What is the physical unit number of DU2:? [O R:0-377 D:2]: >; >; >* CP3036 What is the physical unit number of DU3:? [O R:0-377 D:3]: >; >; >* CP3068 Enter the vector address of DUA [O R:60-774 D:154]: >; >* CP3072 What is its CSR address? [O R:160000-177700 D:172150]: >; >; >; MU: controllers: TK50, TU81, TU81E, TQ81E, RQZX1 >; >* CP3404 How many TMSCP tape controllers do you have? [D R:0.-9. D:0.]: 1 >; >; >* CP3436 What is the physical unit number of MU0:? [O R:0-377 D:0]: >; >; >* CP3468 Enter the vector address of MUA [O R:60-774 D:260]: >; >* CP3472 What is its CSR address? [O R:160000-177700 D:174500]: >; >; VF: Virtual disk/tape driver >; >; >; >; CR: controllers: CM11, CR11 >; >* CP4004 How many CM/CR11 card readers do you have? [O D:0]: >; >; >; CT: controller: TA11 device: TU60 >; >* CP4204 How many TA11 dual cassettes do you have? [O D:0]: >; >; >; MS: controllers: TS11, TU80, TSV05, TK25 >; >* CP4404 How many TS11/TU80/TSV05/TK25 >* magtape controllers do you have? [O D:0]: >; >; >; DT: controller: TC11 device: TU56 >; >* CP4604 How many TC11 DECtape controllers do you have? [O D:0]: >; >; >; DX: controller: RX11 device: RX01 >; >* CP4804 How many RX11 disk controllers do you have? [O D:0]: >; >; >; DY: controller: RX211, RXV21 device: RX02 >; >* CP5004 How many RX211/RXV21 disk controllers do you have? [O D:0]: >; >; >; DD: controller: DL11 device: TU58 >; >* CP5204 How many TU58 controllers do you have? [O D:0]: >; >; >; LP: controllers: LA180, LN01, LP11, LS11, LV11 >; devices: LA180, LG01, LG02, LN01, LP01, LP02, LP04, LP05, >; LP06, LP07, LP14, LP25, LP26, LP27, LS11, LV01 >; >* CP5404 How many LP/LS/LV/LG/LN/LA180 line printers do you have? [O D:0]: 1 >; >* CP5408 Enter the number of seconds between >* line printer-not-ready messages [D R:0.-255. D:15.]: 30. >; >* CP5468 Enter vector address of the next line >* printer [O R:60-774 D:200]: >; >* CP5472 What is its CSR address? [O R:160000-177700 D:177514]: >; >* CP5480 Enter line printer type for LPA [S R:4-5 D:"LP25"]: LS11 >; >* CP5484 Does LPA have lowercase characters? [Y/N D:N]: Y >; >; >; MT: controllers: TM11, TMA11, TMB11 devices: TE10, TU10, TU10W, TS03 >; >* CP5604 How many TM/TMA/TMB11 magtape controllers do you have? [O D:0]: >; >; >; PP: controller: PC11 >; >* CP5804 How many PC11 paper tape reader/punches do you have? [O D:0]: >; >; >; PR: controller: PR11 >; >* CP6004 How many PR11 paper tape readers do you have? [O D:0]: >; >; >; LA: controller: LPA11 >; >* CP6204 How many LPA11 lab subsystems do you have? [D R:0.-16. D:0.]: >; >; >; TT: controllers: DL11, DLV11 controller mnemonic: YL >; >* CP6804 Enter number of additional DL11/DLV11 line interfaces [O D:0]: 1 >; >* CP6820 Do any of the DL11/DLV11 lines require modem support? [Y/N D:N]: >; >* CP6832 Enter terminal type for YLA [S R:4-6 D:"LA120"]: VT52 >; >* CP6868 Enter vector address of YLB [O R:300-770]: 340 >; >* CP6872 What is its CSR address? [O R:160000-177700]: 175640 >; >* CP6832 Enter terminal type for YLB [S R:4-6 D:"LA120"]: VT52 >; >; >; TT: controller: DH11 controller mnemonic: YH >; >* CP7004 Enter number of DH11 asynchronous line >* multiplexers [D R:0.-16. D:0.]: >; >; >; TT: controller mnemonic: YV >; >; controllers: DHU11, DHV11, CXA16, CXB16, CXY08 >; >; >* CP7104 Enter number of DHU11/DHV11/CXA16/CXB16/CXY08 (YV:-type) >* asynchronous line multiplexers [D R:0.-32. D:0.]: >; >; >; TT: controller: DJ11 controller mnemonic: YJ >; >* CP7204 Enter number of DJ11 asynchronous line >* multiplexers [D R:0.-16. D:0.]: >; >; >; TT: controllers: DZ11, DZQ11, DZV11, DFA01 controller mnemonic: YZ >; >* CP7404 Enter number of DZ11/DZQ11/DZV11/DFA01 asynchronous line >* multiplexers [D R:0.-32. D:0.]: >; >; >* CP7604 Do you have any intercomputer communication devices? [Y/N D:N]: >; >; >; Enter device mnemonics for any user-supplied drivers. The driver >; source files must reside in [11,10] and be named ddDRV.MAC and >; ddTAB.MAC where dd is the device mnemonic. >; >; You may enter the mnemonics on more than one line. When you have >; listed all the drivers, press RETURN when asked for the device >; mnemonic. >; >; The device mnemonic must not include a colon. >; >* CP9604 Enter device mnemonics for user-supplied drivers [S]: DW >* CP9604 Enter device mnemonics for user-supplied drivers [S]: MY >* CP9604 Enter device mnemonics for user-supplied drivers [S]: >; >* CP9612 Do you want the DW: driver to be loadable? [Y/N D:N]: Y >; >* CP9616 Do you want the DW: driver's data base to be loadable? [Y/N D:N]: Y >; >* CP9612 Do you want the MY: driver to be loadable? [Y/N D:N]: Y >; >* CP9616 Do you want the MY: driver's data base to be loadable? [Y/N D:N]: Y >; >; >; The highest vector among the devices you specified in this SYSGEN >; is 374(octal). This is the default response for this question. >; >* CP9632 What is the highest interrupt vector >* address? [O R:374-774 D:374]: 774 >; >; >; >;================================================================ >; Assembling the Executive and Drivers 19-JUL-17 at 13:09 >;================================================================ >; >; >; >; The answers to the questions in this section are put in the saved >; answer file [200,200]SYSGENSA1.CMD. >; >!PIP RSXMC3.MAC=RSXMC1.MAC,RSXMC2.MAC >!PIP RSXMC.MAC=RSXMC3.MAC,RSXMC0.MAC >; >!SET /UIC=[1,24] >!PIP [11,10]/NV=[200,200]RSXMC.MAC >!PIP [11,10]/NV=[200,200]SYSTB.MAC >!PIP [11,24]/NV=[200,200]RSXASM.CMD >!PIP [11,24]/NV=[200,200]DRIVERS.ASM >; >; >* AE010 Do you want assembly listings of the Executive and >* drivers? [Y/N D:N]: >; >!ASN NL:=LS: >; >; >* AE030 Do you wish to pause to edit any files before >* assembling? [Y/N D:N]: >; >!SET /UIC=[11,24] >; >!PIP *.OBJ;*/DE/NM,*.TTY;* >; >!TIME >; >!MAC @RSXASM >; >!TIME >; >!MAC @DRIVERS.ASM >; >!TIME >; >!PIP RSX11M.OBS=*.OBJ >!PIP TTDRV.OBS=*.TTY >; >!SET /UIC=[200,200] >!PIP /NV=[11,10]RSXMC.MAC >; >!SET /UIC=[1,24] >!PIP RSXBLD.CMD/PU/NM >!PIP RSX11M.OLB;*/DE/NM >!PIP [200,200]RSXMC.MAC/PU/NM >; >!LBR RSX11M/CR:256.::256./-EP=[11,24]RSX11M.OBS >!PIP [11,24]RSX11M.OBS;*,*.OBJ;*/DE >; >!LBR TTDRV/CR:40.:392.:128.=[11,24]TTDRV.OBS >!PIP [11,24]TTDRV.OBS;*,*.TTY;*/DE >; >; >; >;============================================================== >; Building the Executive and Drivers 19-JUL-17 at 13:09 >;============================================================== >; >; >; >; The answers to the questions in this section are put in the saved >; answer file [200,200]SYSGENSA1.CMD. >; >; >; Allocate space to be used later for the system image file. >; >!SET /UIC=[1,54] >!PIP RSX11M.TMP/CO/BL:1026.=NL: >; >; AT.T0 -- Undefined symbol $U$DAS .IFT $U$DAS .SETS $FCPNM "FCPLRGID" >PIP SYSGEN.CLB;2=SYSGEN.CLB;1 >INS $EDT >LBR SGNEXC=SYSGEN.CLB/EX:SGNEXC >EDT SGNEXC.CMD *EXIT DU0:[200,200]SGNEXC.CMD;2 2245 lines >LBR SYSGEN.CLB/RP=SGNEXC.CMD Module "SGNEXC" replaced > >@SYSGEN >; >; RSX-11M-PLUS V4.6 BL87 SYSGEN >; >; Copyright (c) 1995-1999 by Mentec Inc., U.S.A. >; >SET /DPRO=[RWED,RWED,RWE,R] >; >; To exit from the SYSGEN procedure at any time, type CTRL/Z. >; >; If you are unsure of the answer to a question for which a de- >; fault answer exists, use the default answer. >; >; >; >;=================================================== >; Choosing SYSGEN Options 19-JUL-17 at 13:17 >;=================================================== >; >; >; >; Every question is preceded by a question number (for example SU010) >; which you can use to find the explanation of the question in the >; RSX-11M-PLUS System Generation and Installation Guide. >; >; An explanation of every question is also available by pressing >; the ESC key (or the ALTMODE key) in response to the question. >; >; If you are unfamiliar with the SYSGEN procedure, the explanation of >; each question can be printed automatically before the question. >; >* SU010 Do you always want the explanation printed? [Y/N D:N]: >; >; SYSGEN always creates saved answer files containing your responses >; to the SYSGEN questions: >; >; SYSGENSA1.CMD Setup questions, Executive options >; SYSGENSA2.CMD Peripheral configuration >; SYSGENSA3.CMD Nonprivileged task builds >; >; You should perform a PREPGEN first to create saved answer files, and >; then perform a SYSGEN, specifying those saved answer files as input >; to the Executive, peripheral, and nonprivileged task build sections. >; >* SU020 Do you want to use a saved answer file as input for >* the Executive options? [Y/N D:N]: Y >; >* SU030 Enter saved answer file name [S D:"SYSGENSA1.CMD"]: >; >* SU040 Do you want to use a saved answer file as input for >* the peripheral configuration? [Y/N D:N]: Y >; >* SU050 Enter saved answer file name [S D:"SYSGENSA2.CMD"]: >; >* SU060 Do you want to use a saved answer file as input for >* the nonprivileged task builds? [Y/N D:N]: >; >* SU080 Do you want to do a PREPGEN? [Y/N D:N]: Y >; >* SU090 Enter the name of the disk drive containing your >* target system disk [ddnn:] [S R:2-5]: DU0 >; >ASN DU0:=IN: >ASN DU0:=OU: >ASN DU0:=LB: >ASN DU0:=WK: >ASN DU0:=TK: >ASN DU0:=BC: >ASN DU0:=LI: >ASN DU0:=OB: >ASN DU0:=EX: >ASN DU0:=MP: >; >* SU100 Do you want to run Autoconfigure on the host system >* hardware? [Y/N D:N]: >; >; You can: >; >; o do a complete SYSGEN >; >; o continue a previous SYSGEN from where you left off >; >; o do an individual section of SYSGEN >; >; >* SU120 Do you want to do a complete SYSGEN? [Y/N D:Y]: >; >!INS [3,54]MAC/TASK=MACT0 >!INS [3,54]PIP/TASK=PIPT0 >!INS [3,54]LBR/TASK=LBRT0 >!INS [3,54]TKB/TASK=TKBT0 >!INS [3,54]VMR/TASK=VMRT0 >; >; >; >;====================================================== >; Choosing Executive Options 19-JUL-17 at 13:17 >;====================================================== >; >; >; Using saved answer file DU0:[200,200]SYSGENSA1.CMD;1 >; created on 19-JUL-17 at 12:59:33. >; >; DVK version RSX-11M-PLUS 4.6 >; >; >; >; >;============================================================= >; Choosing Peripheral Configuration 19-JUL-17 at 13:17 >;============================================================= >; >; >; Using saved answer file DU0:[200,200]SYSGENSA2.CMD;1 >; created on 19-JUL-17 at 13:05:19. >; >; DVK version RSX-11M-PLUS 4.6 >; >; >; >; DP: controller: RP11 devices: RP02, RPR02, RP03 >; >; DP Configuration >; >; Physical Unit Number >; >; 0 1 2 3 4 5 6 7 >; >; DPA DP0: DP1: DP2: DP3: DP4: DP5: DP6: DP7: >; >; >; >; DU: controllers: RQZX1, RQDX1, RQDX2, RQDX3, >; RUX50, RQC25, KDA50, UDA50 >; >; devices: RX33, RX50, RD31, RD51, RD52, RD53, RD54, >; RC25, RA60, RA70, RA71, RA72, RA80, RA81, >; RA82, RA90, RA92, RZ23L, RZ24L, RZ26x, RZ29B >; >; The total of DU and MU controllers cannot be greater than 10. >; >; >; MU: controllers: TK50, TU81, TU81E, TQ81E, RQZX1 >; >; VF: Virtual disk/tape driver >; >; >; >; LP: controllers: LA180, LN01, LP11, LS11, LV11 >; devices: LA180, LG01, LG02, LN01, LP01, LP02, LP04, LP05, >; LP06, LP07, LP14, LP25, LP26, LP27, LS11, LV01 >; >; >; TT: controllers: DL11, DLV11 controller mnemonic: YL >; >; >; >;================================================================ >; Assembling the Executive and Drivers 19-JUL-17 at 13:17 >;================================================================ >; >; >!PIP RSXMC3.MAC=RSXMC1.MAC,RSXMC2.MAC >!PIP RSXMC.MAC=RSXMC3.MAC,RSXMC0.MAC >; >!SET /UIC=[1,24] >!PIP [11,10]/NV=[200,200]RSXMC.MAC >!PIP [11,10]/NV=[200,200]SYSTB.MAC >!PIP [11,24]/NV=[200,200]RSXASM.CMD >!PIP [11,24]/NV=[200,200]DRIVERS.ASM >; >; >!ASN NL:=LS: >; >; >!SET /UIC=[11,24] >; >!PIP *.OBJ;*/DE/NM,*.TTY;* >; >!TIME >; >!MAC @RSXASM >; >!TIME >; >!MAC @DRIVERS.ASM >; >!TIME >; >!PIP RSX11M.OBS=*.OBJ >!PIP TTDRV.OBS=*.TTY >; >!SET /UIC=[200,200] >!PIP /NV=[11,10]RSXMC.MAC >; >!SET /UIC=[1,24] >!PIP RSXBLD.CMD/PU/NM >!PIP RSX11M.OLB;*/DE/NM >!PIP [200,200]RSXMC.MAC/PU/NM >; >!LBR RSX11M/CR:256.::256./-EP=[11,24]RSX11M.OBS >!PIP [11,24]RSX11M.OBS;*,*.OBJ;*/DE >; >!LBR TTDRV/CR:40.:392.:128.=[11,24]TTDRV.OBS >!PIP [11,24]TTDRV.OBS;*,*.TTY;*/DE >; >; >; >;============================================================== >; Building the Executive and Drivers 19-JUL-17 at 13:17 >;============================================================== >; >; >; >; Allocate space to be used later for the system image file. >; >!SET /UIC=[1,54] >!PIP RSX11M.TMP/CO/BL:1026.=NL: >; >; >!SET /UIC=[1,54] >!PIP SYSVMR.CMD=[200,200]SYSVMR.CMD,VMRTTY.CMD >; >; >* BE030 Do you want to pause to edit any files before >* task-building? [Y/N D:N]: >; >!SET /UIC=[1,24] >!PIP [1,24]/NV/NM=[200,200]RSXBLD.CMD,RSX11M,DSP11M,LDR11M >!PIP [1,24]/NV=[200,200]DIR11M.CMD,DR211M,DIRCOM,DR2COM,DIR >!PIP [1,24]/NV=[200,200]DR311M.CMD,DR411M,DR3COM,DR4COM >!PIP [1,24]/NV=[200,200]VEC11M.CMD,DCM11M,VECCOM >; >!TIME >; >!TKB @RSXBLD >; >!TIME >; >!TKB @[200,200]DRIVERS.BLD >; >!TIME >; >; >; >;========================================================= >; Building the Privileged Task 19-JUL-17 at 13:18 >;========================================================= >; >; >; >* BP040 Do you want the maps of the privileged tasks? [Y/N D:N]: Y >; >* BP050 What is to be the map device [ddu:]? [S R:2-5 D:"SY:"]: >; >!ASN SY:=MP: >; >!SET /UIC=[1,24] >; >!TIME >; >!TKB @SAVBLD >; >!TIME >; >!ASN LB:=OU: >; >; >; >;============================================================ >; Rebuilding Supplied System Tasks 19-JUL-17 at 13:18 >;============================================================ >; >; >; >; The answers to the questions in this section are put in the saved >; answer file [200,200]SYSGENSA3.CMD. >; >; >* BN010 Do you want to rebuild any system tasks? [Y/N D:N]: Y >; >; Enter a comment for inclusion in the SYSGENSA3 saved answer file. >; The comment may contain more than one line. The "V" in the right >; margin below marks the maximum line length. When you are done, >; press RETURN in response to the prompt. >; V >* Comment [S R:0.-55.]: DVK version RSX-11M-PLUS 4.6 >* Comment [S R:0.-55.]: >; >* BN012 Use FCSRES when possible? [Y/N D:Y]: Y >; >; Press ESC for the list of the nonprivileged utilities and >; vectored privileged system tasks that may be rebuilt here. >; >; Enter ALL to build all the tasks, using FCSRES. >; Enter ALLVAN to build all tasks, not using the FCS libraries. >; Enter ALLRES to build all the FCSRES tasks. >; >; SYSGEN will attempt to use FCSRES where possible. >; >; Enter the task names separated by commas. You can enter them on >; more than one line. When you are done, finish the list with a >; period or press RETURN in response to the prompt. >; >* BN020 Enter task name(s) [S]: ALL >* BN020 Enter task name(s) [S]: >; >; >* BN030 Do you want the maps of the system tasks? [Y/N D:N]: Y >; >* BN040 What is to be the map device [ddu:]? [S R:2-5 D:"SY:"]: >; >!ASN SY:=MP: >; >* BN050 Do you want to pause to edit any files before >* task-building? [Y/N D:N]: >!SET /UIC=[1,24] >; >; >!TKB @ACDBLD >!TKB @BADBLD >!TKB @BOOBLD >!TKB @BROBLD >!TKB @BRUBLD >!TKB @BYEBLD >!TKB @CFLBLD >!TKB @CONBLD >!TKB @CRPBLD >!TKB @DCLBLD >!TKB @DLDBLD >!TKB @DMOBLD >!TKB @DTEBLD >!TKB @ERLBLD >!TKB @FMTBLD >!TKB @FXRBLD >!TKB @HRCBLD >!TKB @INIBLD >!TKB @INSBLD >!TKB @LOABLD >!TKB @MCDBLD >!TKB @MCRBLD >!TKB @MFTBLD >!TKB @MOUBLD >!TKB @MTABLD >!TKB @PMTBLD >!TKB @QCLBLD >!TKB @QPRBLD >!TKB @RCTBLD >!TKB @RMDBLD >!TKB @RPTBLD >!TKB @SHABLD >!TKB @SHFBLD >!TKB @SHUBLD >!TKB @TDXBLD >!TKB @TKNBLD >!TKB @UFDBLD >!TKB @UMLBLD >!TKB @VMRBLD >!TKB @XDTBLD >!TKB @ACCRESBLD >!TKB @ACNRESBLD >!TKB @ACSRESBLD >!TKB @CDARESBLD >!TKB @CMPRESBLD >!TKB @COTRESBLD >!TKB @CRFRESBLD >!TKB @DMPRESBLD >!TKB @EDIRESBLD >!TKB @EDTRESBLD >!TKB @ELIRESBLD >!TKB @FLXRESBLD >!TKB @FTBRESBLD >!TKB @HELRESBLD >!TKB @ICMRESBLD >!TKB @IPPRESBLD >!TKB @IOXRESBLD >!TKB @LBRRESBLD >!TKB @LPPRESBLD >!TKB @MACRESBLD >!TKB @PATRESBLD >!TKB @PIPRESBLD >!TKB @PMDRESBLD >!TKB @PSWRESBLD >!TKB @QMGRESBLD >!TKB @SLPRESBLD >!TKB @SYLRESBLD >!TKB @TKBRESBLD >!TKB @UNLRESBLD >!TKB @VFYRESBLD >!TKB @ZAPRESBLD >; >; >; >; >;========================================================== >; Creating the System Image File 19-JUL-17 at 13:19 >;========================================================== >; >; >!SET /UIC=[1,54] >; >!PIP RSX11M.TMP;*/DE/NM >; >!PIP RSX11M.SYS/CO/NV/BL:1026.=RSX11M.TSK >; >!ASN LB:=SY: >!VMR @SYSVMR >; >!REM MACT0 >!REM PIPT0 >!REM LBRT0 >!REM TKBT0 >!REM VMRT0 >; >; End of PREPGEN >; >TIME 13:19:39 19-JUL-17 >; >ASN = >; >@ >PIP SYSGEN*.CMD;*/PU >PIP SGNSYM1.CMD;1=SGNSYM1.CMD;2/RE >PIP SGNSYM2.CMD;1=SGNSYM2.CMD;2/RE >PIP SYSGENSA1.CMD;1=SYSGENSA1.CMD;2/RE >PIP SYSGENSA2.CMD;1=SYSGENSA2.CMD;2/RE > >@SYSGEN >; >; RSX-11M-PLUS V4.6 BL87 SYSGEN >; >; Copyright (c) 1995-1999 by Mentec Inc., U.S.A. >; >SET /DPRO=[RWED,RWED,RWE,R] >; >; To exit from the SYSGEN procedure at any time, type CTRL/Z. >; >; If you are unsure of the answer to a question for which a de- >; fault answer exists, use the default answer. >; >; >; >;=================================================== >; Choosing SYSGEN Options 19-JUL-17 at 13:25 >;=================================================== >; >; >; >; Every question is preceded by a question number (for example SU010) >; which you can use to find the explanation of the question in the >; RSX-11M-PLUS System Generation and Installation Guide. >; >; An explanation of every question is also available by pressing >; the ESC key (or the ALTMODE key) in response to the question. >; >; If you are unfamiliar with the SYSGEN procedure, the explanation of >; each question can be printed automatically before the question. >; >* SU010 Do you always want the explanation printed? [Y/N D:N]: >; >; SYSGEN always creates saved answer files containing your responses >; to the SYSGEN questions: >; >; SYSGENSA1.CMD Setup questions, Executive options >; SYSGENSA2.CMD Peripheral configuration >; SYSGENSA3.CMD Nonprivileged task builds >; >; You should perform a PREPGEN first to create saved answer files, and >; then perform a SYSGEN, specifying those saved answer files as input >; to the Executive, peripheral, and nonprivileged task build sections. >; >* SU020 Do you want to use a saved answer file as input for >* the Executive options? [Y/N D:N]: Y >; >* SU030 Enter saved answer file name [S D:"SYSGENSA1.CMD"]: >; >* SU040 Do you want to use a saved answer file as input for >* the peripheral configuration? [Y/N D:N]: Y >; >* SU050 Enter saved answer file name [S D:"SYSGENSA2.CMD"]: >; >* SU060 Do you want to use a saved answer file as input for >* the nonprivileged task builds? [Y/N D:N]: Y >; >* SU070 Enter saved answer file name [S D:"SYSGENSA3.CMD"]: >; >* SU080 Do you want to do a PREPGEN? [Y/N D:N]: >; >* SU090 Enter the name of the disk drive containing your >* target system disk [ddnn:] [S R:2-5]: DU0 >; >ASN DU0:=IN: >ASN DU0:=OU: >ASN DU0:=LB: >ASN DU0:=WK: >ASN DU0:=TK: >ASN DU0:=BC: >ASN DU0:=LI: >ASN DU0:=OB: >ASN DU0:=EX: >ASN DU0:=MP: >; >* SU100 Do you want to run Autoconfigure on the host system >* hardware? [Y/N D:N]: >; >; You can: >; >; o do a complete SYSGEN >; >; o continue a previous SYSGEN from where you left off >; >; o do an individual section of SYSGEN >; >; >* SU120 Do you want to do a complete SYSGEN? [Y/N D:Y]: >; >INS [3,54]MAC/TASK=MACT0 >INS [3,54]PIP/TASK=PIPT0 >INS [3,54]LBR/TASK=LBRT0 >INS [3,54]TKB/TASK=TKBT0 >INS [3,54]VMR/TASK=VMRT0 >; >; >; >;====================================================== >; Choosing Executive Options 19-JUL-17 at 13:25 >;====================================================== >; >; >; Using saved answer file DU0:[200,200]SYSGENSA1.CMD;1 >; created on 19-JUL-17 at 13:17:39. >; >; DVK version RSX-11M-PLUS 4.6 >; >; >; >; >;============================================================= >; Choosing Peripheral Configuration 19-JUL-17 at 13:25 >;============================================================= >; >; >; Using saved answer file DU0:[200,200]SYSGENSA2.CMD;1 >; created on 19-JUL-17 at 13:17:39. >; >; DVK version RSX-11M-PLUS 4.6 >; >; >; >; DP: controller: RP11 devices: RP02, RPR02, RP03 >; >; DP Configuration >; >; Physical Unit Number >; >; 0 1 2 3 4 5 6 7 >; >; DPA DP0: DP1: DP2: DP3: DP4: DP5: DP6: DP7: >; >; >; >; DU: controllers: RQZX1, RQDX1, RQDX2, RQDX3, >; RUX50, RQC25, KDA50, UDA50 >; >; devices: RX33, RX50, RD31, RD51, RD52, RD53, RD54, >; RC25, RA60, RA70, RA71, RA72, RA80, RA81, >; RA82, RA90, RA92, RZ23L, RZ24L, RZ26x, RZ29B >; >; The total of DU and MU controllers cannot be greater than 10. >; >; >; MU: controllers: TK50, TU81, TU81E, TQ81E, RQZX1 >; >; VF: Virtual disk/tape driver >; >; >; >; LP: controllers: LA180, LN01, LP11, LS11, LV11 >; devices: LA180, LG01, LG02, LN01, LP01, LP02, LP04, LP05, >; LP06, LP07, LP14, LP25, LP26, LP27, LS11, LV01 >; >; >; TT: controllers: DL11, DLV11 controller mnemonic: YL >; >; >; >;================================================================ >; Assembling the Executive and Drivers 19-JUL-17 at 13:25 >;================================================================ >; >; >PIP RSXMC3.MAC=RSXMC1.MAC,RSXMC2.MAC >PIP RSXMC.MAC=RSXMC3.MAC,RSXMC0.MAC >; >SET /UIC=[1,24] >PIP [11,10]/NV=[200,200]RSXMC.MAC >PIP [11,10]/NV=[200,200]SYSTB.MAC >PIP [11,24]/NV=[200,200]RSXASM.CMD >PIP [11,24]/NV=[200,200]DRIVERS.ASM >; >; >ASN NL:=LS: >; >; >SET /UIC=[11,24] >; >PIP *.OBJ;*/DE/NM,*.TTY;* >; >TIME 13:25:54 19-JUL-17 >; >MAC @RSXASM >; >TIME 13:27:28 19-JUL-17 >; >MAC @DRIVERS.ASM >; >TIME 13:28:41 19-JUL-17 >; >PIP RSX11M.OBS=*.OBJ >PIP TTDRV.OBS=*.TTY >; >SET /UIC=[200,200] >PIP /NV=[11,10]RSXMC.MAC >; >SET /UIC=[1,24] >PIP RSXBLD.CMD/PU/NM >PIP RSX11M.OLB;*/DE/NM >PIP [200,200]RSXMC.MAC/PU/NM >; >LBR RSX11M/CR:256.::256./-EP=[11,24]RSX11M.OBS >PIP [11,24]RSX11M.OBS;*,*.OBJ;*/DE >; >LBR TTDRV/CR:40.:392.:128.=[11,24]TTDRV.OBS >PIP [11,24]TTDRV.OBS;*,*.TTY;*/DE >SET /UIC=[200,200] >; >; >; >;============================================================== >; Building the Executive and Drivers 19-JUL-17 at 13:28 >;============================================================== >; >; >; >; Allocate space to be used later for the system image file. >; >SET /UIC=[1,54] >PIP RSX11M.TMP/CO/BL:1026.=NL: >; >SET /UIC=[200,200] >; >SET /UIC=[1,24] >SET /UIC=[200,200] >SET /UIC=[1,54] >PIP SYSVMR.CMD=[200,200]SYSVMR.CMD,VMRTTY.CMD >; >SET /UIC=[200,200] >; >SET /UIC=[1,24] >PIP [1,24]/NV/NM=[200,200]RSXBLD.CMD,RSX11M,DSP11M,LDR11M >PIP [1,24]/NV=[200,200]DIR11M.CMD,DR211M,DIRCOM,DR2COM,DIR >PIP [1,24]/NV=[200,200]DR311M.CMD,DR411M,DR3COM,DR4COM >PIP [1,24]/NV=[200,200]VEC11M.CMD,DCM11M,VECCOM >; >TIME 13:28:46 19-JUL-17 >; >TKB @RSXBLD >; >TIME 13:29:10 19-JUL-17 >; >TKB @[200,200]DRIVERS.BLD >; >TIME 13:29:15 19-JUL-17 >SET /UIC=[200,200] >; >; >; >;========================================================= >; Building the Privileged Task 19-JUL-17 at 13:29 >;========================================================= >; >; >; >ASN SY:=MP: >; >SET /UIC=[1,24] >; >TIME 13:29:15 19-JUL-17 >; >TKB @SAVBLD >; >TIME 13:29:20 19-JUL-17 >; >ASN LB:=OU: >SET /UIC=[200,200] >; >; >; >;============================================================ >; Rebuilding Supplied System Tasks 19-JUL-17 at 13:29 >;============================================================ >; >; >; >SET /UIC=[1,24] >SET /UIC=[200,200] >; >ASN SY:=MP: >SET /UIC=[1,24] >; >; >TKB @ACDBLD >TKB @BADBLD >TKB @BOOBLD >TKB @BROBLD >TKB @BRUBLD >TKB @BYEBLD >TKB @CFLBLD >TKB @CONBLD >TKB @CRPBLD >TKB @DCLBLD >TKB @DLDBLD >TKB @DMOBLD >TKB @DTEBLD >TKB @ERLBLD >TKB @FMTBLD >TKB @FXRBLD >TKB @HRCBLD >TKB @INIBLD >TKB @INSBLD >TKB @LOABLD >TKB @MCDBLD >TKB @MCRBLD >TKB @MFTBLD >TKB @MOUBLD >TKB @MTABLD >TKB @PMTBLD >TKB @QCLBLD >TKB @QPRBLD >TKB @RCTBLD >TKB @RMDBLD >TKB @RPTBLD >TKB @SHABLD >TKB @SHFBLD >TKB @SHUBLD >TKB @TDXBLD >TKB @TKNBLD >TKB @UFDBLD >TKB @UMLBLD >TKB @VMRBLD >TKB @XDTBLD >TKB @ACCRESBLD >TKB @ACNRESBLD >TKB @ACSRESBLD >TKB @CDARESBLD >TKB @CMPRESBLD >TKB @COTRESBLD >TKB @CRFRESBLD >TKB @DMPRESBLD >TKB @EDIRESBLD >TKB @EDTRESBLD >TKB @ELIRESBLD >TKB @FLXRESBLD >TKB @FTBRESBLD >TKB @HELRESBLD >TKB @ICMRESBLD >TKB @IPPRESBLD >TKB @IOXRESBLD >TKB @LBRRESBLD >TKB @LPPRESBLD >TKB @MACRESBLD >TKB @PATRESBLD >TKB @PIPRESBLD >TKB @PMDRESBLD >TKB @PSWRESBLD >TKB @QMGRESBLD >TKB @SLPRESBLD >TKB @SYLRESBLD >TKB @TKBRESBLD >TKB @UNLRESBLD >TKB @VFYRESBLD >TKB @ZAPRESBLD >; >SET /UIC=[200,200] >; >; >; >;========================================================== >; Creating the System Image File 19-JUL-17 at 13:34 >;========================================================== >; >; >SET /UIC=[1,54] >; >PIP RSX11M.TMP;*/DE/NM >; >PIP RSX11M.SYS/CO/NV/BL:1026.=RSX11M.TSK >; >ASN LB:=SY: >VMR @SYSVMR VMR -- *DIAG*-Installed tasks or commons may no longer fit in partition SET /TOP=SYSPAR:-* VMR -- *DIAG*-Loadable driver larger than 4K LOA TT:/SIZE=16300 VMR -- *DIAG*-Installed tasks or commons may no longer fit in partition SET /TOP=DRVPAR:-* SECPOL 117734 00120000 00100000 SEC POOL SYSPAR 117670 00220000 00201000 MAIN 117624 00220000 00111300 RO COM !DIR11M! 117440 00331300 00004400 TASK [...LDR] 117240 00335700 00033500 TASK [MCR...] 117040 00371400 00010500 TASK [TKTN ] 116640 00402100 00003200 TASK [SHF...] 116440 00405300 00013500 TASK [RCT...] DRVPAR 116360 00421000 00131700 MAIN 116314 00421000 00006300 RO COM !TTEXT ! 116230 00427300 00036000 DRIVER (TT:) 115260 00465300 00001400 DRIVER (DP:) 115174 00466700 00005100 RO COM !PUCOM ! 114374 00474000 00014000 DRIVER (DU:) 114020 00510000 00011500 DRIVER (MU:) 113560 00521500 00001300 DRIVER (LP:) 113350 00523000 00000100 DRIVER (NL:) 113304 00523100 00017700 DRIVER (VF:) 113240 00543000 00002500 DRIVER (VT:) 113174 00545500 00001500 DRIVER (RD:) 112544 00547200 00001700 DRIVER (DW:) 112134 00551100 00001600 DRIVER (MY:) GEN 112050 00552700 03225100 MAIN ...LDR 12.01 117504 SYSPAR 248. 00004400 LB0:-00110435 FIXED TKTN 07.01 117104 SYSPAR 248. 00010500 LB0:-00167623 FIXED F11MSG 15.00 110160 GEN 200. 00006300 LB0:-00045045 MTAACP 17.00 107600 GEN 200. 00016200 LB0:-00165056 MCR... 07.00 117304 SYSPAR 160. 00033500 LB0:-00163241 FIXED F11ACP 07.00 111640 GEN 149. 00011100 LB0:-00043515 ERRLOG 05.03 111310 GEN 148. 00056200 LB0:-00162072 PMT... 02.02 110660 GEN 148. 00007500 LB0:-00164767 HRC... 05.00 107720 GEN 140. 00042500 LB0:-00162407 PMD... 07.05 107460 GEN 140. 00017600 LB0:-00176037 SYSLOG 04.03 110420 GEN 130. 00024500 LB0:-00176273 SHF... 07.01 116704 SYSPAR 105. 00003200 LB0:-00167260 FIXED RCT... 06.02 116504 SYSPAR 100. 00013500 LB0:-00165016 FIXED FXR... 03.02 110040 GEN 100. 00003300 LB0:-00162333 BAP0 04.11 111430 GEN 80. 00050300 LB0:-00035350 QMG... 06.04 110540 GEN 75. 00037300 LB0:-00176144 LP0 07.04 111074 GEN 70. 00020300 LB0:-00175112 ACNT 06.04 110300 GEN 50. 00057600 LB0:-00171055 SHUTUP 04.04 107340 GEN 50. 00016500 LB0:-00167277 ...RMD 05.00 001236+ GEN 225. 00042000 LB0:-00166131 ...DCL 06.01 001212+ GEN 160. 00062500 LB0:-00160531 ...DMO 04.02 001214+ GEN 160. 00017300 LB0:-00160437 ...MCR 07.00 001230+ GEN 160. 00040300 LB0:-00163525 ...MOU 26.06 001232+ GEN 160. 00045600 LB0:-00163277 ...CA. 01.00 001264+ GEN 150. 00026100 LB0:-00167573 ...INS 16.00 001226+ GEN 100. 00053200 LB0:-00162666 ...SAV 11.00 001262+ GEN 100. 00070500 LB0:-00155014 ...UFD 07.02 001266+ GEN 100. 00014500 LB0:-00167677 ...VCP V04.10 001270+ GEN 90. 00020300 LB0:-00056757 ...ACS 04.00 001244+ GEN 70. 00006200 LB0:-00171153 ...ACC 05.00 001204+ GEN 65. 00032100 LB0:-00170717 ...AT. 10.0 001220+ GEN 64. 00056700 LB0:-00174077 ...INI 24.00 001222+ GEN 60. 00037200 LB0:-00162536 ...HOM 24.00 001224+ GEN 60. 00037200 LB0:-00162536 ...BRO 09.10 001206+ GEN 50. 00041500 LB0:-00156725 ...BYE 05.01 001210+ GEN 50. 00021700 LB0:-00156773 ...HEL 06.00 001216+ GEN 50. 00031600 LB0:-00173637 ...PIP 21.00 001234+ GEN 50. 00036400 LB0:-00175723 ...UNL 05.04 001240+ GEN 50. 00021500 LB0:-00176341 ...ACD 03.00 001242+ GEN 50. 00042500 LB0:-00156412 ...BOO 03.10 001246+ GEN 50. 00047200 LB0:-00156623 ...CON 05.00 001250+ GEN 50. 00135600 LB0:-00157705 ...ELI 04.03 001252+ GEN 50. 00032600 LB0:-00172352 ...LOA 05.03 001254+ GEN 50. 00040000 LB0:-00163017 ...MAG 03.00 001256+ GEN 50. 00037300 LB0:-00164712 ...PSW 03.02 001260+ GEN 50. 00017500 LB0:-00176111 YLA OFL CPA CSR=177560 VEC=60 PRI=5 YLB OFL CPA CSR=175640 VEC=340 PRI=5 DPA OFL CPA CSR=176714 VEC=254 PRI=5 DUA OFL CPA CSR=172150 VEC=154 PRI=5 MUA OFL CPA CSR=174500 VEC=260 PRI=5 LPA OFL CPA CSR=177514 VEC=200 PRI=4 DWA OFL CPA CSR=174020 VEC=300 PRI=4 DWB OFL CPA CSR=174060 VEC=310 PRI=4 MYA OFL CPA CSR=172140 VEC=170 PRI=5 VF0: OFL DRIVER VF1: OFL DRIVER VF2: OFL DRIVER VF3: OFL DRIVER VF4: OFL DRIVER VF5: OFL DRIVER VF6: OFL DRIVER VF7: OFL DRIVER VF10: OFL DRIVER VF11: OFL DRIVER VF12: OFL DRIVER VF13: OFL DRIVER VF14: OFL DRIVER VF15: OFL DRIVER VF16: OFL DRIVER VF17: OFL DRIVER TT0: YLA0: OFL DRIVER TT1: YLB0: OFL DRIVER VT0: OFL DRIVER RD0: ONL DRIVER DP0: DPA0: OFL DRIVER DP1: DPA1: OFL DRIVER DP2: DPA2: OFL DRIVER DP3: DPA3: OFL DRIVER DP4: DPA4: OFL DRIVER DP5: DPA5: OFL DRIVER DP6: DPA6: OFL DRIVER DP7: DPA7: OFL DRIVER DU0: DUA0: OFL DRIVER DU1: DUA1: OFL DRIVER DU2: DUA2: OFL DRIVER DU3: DUA3: OFL DRIVER MU0: MUA0: OFL DRIVER LP0: LPA0: OFL DRIVER NL0: OFL DRIVER DW0: DWA0: OFL DRIVER DW1: DWB0: OFL DRIVER MY0: MYA0: OFL DRIVER MY1: MYA1: OFL DRIVER POOL=1200:4668.:04668.:1200 >SET /UIC=[200,200] >; >REM MACT0 >REM PIPT0 >REM LBRT0 >REM TKBT0 >REM VMRT0 >; >; End of SYSGEN >; >TIME 13:34:39 19-JUL-17 >; >ASN = >; >@ >RUN $SHUTUP RSX-11M-PLUS Shut down program Enter minutes to wait before shutdown: Reason for shutdown ( for none): OK to shutdown? [Y/N]: Y All further logins are disabled 19-JUL-17 13:35 System is now shutting down -- BASLIN QUE /STO:QMG > STOP/ACCOUNTING SHUTUP 13:35:16 SYSLOG -- 47. Exiting > @LB:[1,2]SHUTUP >@ > ELI /NOLOG > ACS DU0:/BLKS=0. ACS -- Checkpoint file now inactive > DMO DU0:/DEV/LOCK=V DMO -- System disk being dismounted DMO -- SYSTEM dismounted from DU0: *** Final dismount initiated *** 13:35:17 *** DU0: -- Dismount complete > DMO DU1:/DEV/LOCK=V DMO -- Warning - Tasks installed from DU1: DMO -- SYSTEM dismounted from DU1: *** Final dismount initiated *** 13:35:22 *** DU1: -- Dismount complete > SHUTUP operation complete Logins are now enabled >MOU DU:/OVR/VI Volume Information Class: Files-11 Device: DU00 Volume label:RSX11MPBL87 Pack serial: 00000001236 Owner: [1,1] Protection: [RWCD,RWCD,RWCD,RWCD] Default: [RWED,RWED,RWED,R] Processor: F11ACP >BOO DU:[1,54] RSX-11M-PLUS V4.6 BL87 > >SAV /WB RSX-11M-PLUS V4.6 BL87 2044.KW System:"KPXX01" >RED DU:=SY: >RED DU:=LB: >RED DU:=SP: >MOU DU0:"RSX11MPBL87" >@DU:[1,2]STARTUP >; PLEASE NOTE >; >; If you have not yet read the system release notes, please do so >; now before attempting to perform a SYSGEN or to utilize the new >; features of this system. >; >; >* Please enter time and date (Default:19-JUL-2017 13:47) [S]: >ACS SY:/BLKS=1024. >CON ONLINE ALL >ELI /LOG/LIM >CLI /INIT=DCL/CTRLC/DPR="<15><12>/$ /" >INS LB:[1,1]RMSRESAB.TSK/RON=YES/PAR=GEN >INS LB:[1,1]RMSLBL.TSK/RON=YES/PAR=GEN >INS LB:[1,1]RMSLBM.TSK/RON=YES/PAR=GEN >INS $QMGCLI >INS $QMGCLI/TASK=...PRI >INS $QMGCLI/TASK=...SUB >QUE /START:QMG >INS $QMGPRT/TASK=PRT.../SLV=NO >QUE LP0:/CR/NM >START/ACCOUNTING >CON ESTAT LP0: >QUE LP0:/SP/FL:2/LOWER/FO:0 >QUE BAP0:/BATCH >QUE LP0:/AS:PRINT >QUE BAP0:/AS:BATCH >@ >BYE Have a Good Afternoon 2017-07-19 13:54 TT0: logged off KPXX01 > >HEL 10/1/xxx RSX-11M-PLUS V4.6 BL87 [1,54] System KPXX01 2017-07-19 13:54 Logged on Terminal TT0: as KXX1 Good Afternoon Last interactive login on Wednesday, 2017-07-19 12:45:48 (TT0:) >@LOGIN.CMD >SET /EBC=TI: >MOU DU1:/OVR/VI/PUB Volume Information Class: Files-11 Device: DU01 Volume label:HUNTA Pack serial: 00000001235 Owner: [1,1] Protection: [RWCD,RWCD,RWCD,RWCD] Default: [RWED,RWED,RWED,R] Processor: F11ACP >REM ...CA. >INS DU1:[4,54]CCLRES.TSK/TASK=...CA. >INS DU1:[4,54]CCL.TSK/TASK=...CA0 >INS DU1:[4,54]POLICE/TASK=...CA1 >INS DU1:[1,1]NDTBAS/RON=YES/PAR=GEN >INS DU1:[1,1]MIMRES/RON=YES/PAR=GEN >INS $BAD >INS $BRU >INS $CMP >INS $CRF >INS $DMP >INS $LBR >INS $MAC >INS $RPT >INS $SLP >INS $TKB >INS $VFY >INS $VMR >INS $ZAP >INS DU1:[4,54]BICRES >INS DU1:[4,54]DUP/INC=18000. >INS DU1:[4,54]ERR >INS DU1:[4,54]MIMRES >INS DU1:[4,54]MIMRES/TASK=...NDT >INS DU1:[4,54]MIMRES/TASK=...MMM >INS DU1:[4,54]MO >INS DU1:[4,54]SRDRES >ACD REMOVE NUMBER 20 That ACD is not installed >ACD INSTALL DU1:[ACD2]MIMACD.TSK AS NUMBER 20 ASSIGN ACD$MIM >ACD LINK TI: TO NUMBER 20 >@